Mold colonies in crawl spaces originate at ground level and migrate upward through your home's air supply. JCB Waterproofing and Construction installs certified encapsulation systems that cut off moisture at the source.
What makes our encapsulation installs last decades, not years.
We install 20-mil reinforced polyethylene vapor barriers -- not the thin 6-mil sheeting that degrades within a few years under crawl space conditions.
We seal every penetration -- pipes, posts, and support columns -- individually so the barrier is continuous with no gaps that allow moisture to bypass the system.
HVAC equipment running in an encapsulated crawl space operates at higher efficiency because humidity does not overload the system's dehumidification capacity.
Wood floor joists exposed to sustained humidity above 20 percent begin to lose structural integrity within a few years -- encapsulation stops that deterioration before it becomes expensive.
Crawl space encapsulation is the process of sealing a home's crawl space against outside air and ground moisture by installing a continuous vapor barrier on the floor and walls, sealing all vents and penetrations, and managing the internal humidity of the sealed space with a dedicated dehumidifier or conditioned air supply. The result is a semi-conditioned space that behaves like a dry indoor environment rather than an extension of the outside soil -- eliminating the ground moisture evaporation that is the primary driver of crawl space mold and wood rot. In Kimberton, PA, where soil moisture conditions fluctuate significantly with the seasons, encapsulation provides consistent protection year-round that passive venting strategies cannot match.
The vapor barrier is the physical core of the encapsulation system. Mil thickness matters significantly in this application: 6-mil poly is standard for short-term vapor retarders in above-grade construction, but crawl space conditions include foot traffic during inspections and maintenance, contact with rough aggregate and irregular soil surfaces, rodent activity, and exposure to moisture for decades. We specify a minimum 20-mil reinforced poly with a ripstop layer that resists puncture from debris and maintains its vapor transmission rating even if the surface is scuffed or walked on. The barrier is cut and fitted to the exact dimensions of each crawl space section, with all wall terminations run up to the rim joist and sealed with a waterproof tape rated for that adhesion surface.
HVAC performance in homes with encapsulated crawl spaces improves because the humidity load on the air conditioning system is reduced. In a vented crawl space, humid outside air is drawn under the house, rises through the subfloor into the living space, and must be removed by the air conditioning system. This hidden moisture load causes air conditioners to run longer, increases compressor wear, and reduces the effective cooling capacity of the system. After encapsulation, the crawl space humidity is maintained by a rated standalone dehumidifier that handles only the manageable internal moisture load rather than an endless supply from outside air.
Crawl space dehumidification is the final element of a complete encapsulation system. Even a fully sealed crawl space generates some internal humidity from concrete foundation walls and the residual moisture in the soil, particularly in the first season after installation when the soil is transitioning to a lower equilibrium moisture content. A rated crawl space dehumidifier sized to the cubic footage of the space maintains interior relative humidity below the threshold that supports mold growth. We specify units with gravity drain or condensate pump to eliminate the manual emptying requirement, and we set the humidistat to an appropriate setpoint for Kimberton, PA conditions before completing each project.
Complete coverage from vapor barrier to dehumidification -- everything your crawl space needs.
20-mil reinforced poly barrier installed across the entire crawl space floor and up foundation walls, sealed at all seams and penetrations for complete moisture control.
Dehumidifier placement and airflow direction are planned to ensure even coverage of the entire sealed space, with no humidity pockets that allow localized moisture buildup.
Existing foundation vents are sealed with rigid foam insulation cut to size and adhered with spray foam to eliminate the primary pathway for outside humid air to enter the crawl space.
When visible mold colonies are present on floor joists, sheathing, or structural framing, we treat affected surfaces with EPA-registered fungicidal solutions before installing the vapor barrier.
Drainage channels are integrated under the vapor barrier perimeter, routing water to a sump pit with a submersible pump sized for your drainage area.
Existing crawl space access hatches and exterior doors are insulated and sealed to prevent air infiltration that would bypass the encapsulation system at its perimeter.
We enter the crawl space and conduct a systematic inspection of all floor and wall surfaces, document moisture meter readings at multiple locations, photograph all floor joist and beam conditions, and identify every source of water or moisture entry before recommending any course of action.
Where mold remediation is needed, we complete EPA-registered fungicidal treatment and borate application before any encapsulation materials are installed, ensuring no active mold is sealed under the barrier.
Heavy-duty vapor barrier material is measured, cut, and installed across every section of the crawl space floor and up foundation walls, with all seams overlapped and taped and all penetrations individually sealed.
A rated crawl space dehumidifier is installed, connected to gravity drain or a condensate pump, and set to the target humidity level for your Kimberton, PA climate before we complete the project.
Our floor joists were showing early decay when JCB Waterproofing and Construction inspected. They remediated the mold, sealed the entire crawl space, and installed a dehumidifier -- a year later the wood moisture readings are in the safe range and the floors feel solid again.
The crew was thorough and professional. They explained what they found, showed me photos, and completed the work exactly as quoted. The crawl space is completely dry now and looks professionally done.
The air quality in our home is noticeably better since the encapsulation. I have less allergy issues and our HVAC is running shorter cycles. Genuinely one of the best home improvements we have made.
Take the first step toward a healthier, drier home. Contact JCB Waterproofing and Construction for a same-day crawl space inspection.
Call +1-866-476-1348 Now